Products Range

/Products Range
Products Range2019-11-06T10:45:58+00:00

Low Voltage Switchgear

Low voltage switchgear for Industrial, commercial and residential sectors are being manufactured as per requirement of the client. The switchgear may be indoor or outdoor type in various international protection standards. The cubicles are designed, fabricated with front and rear access, wired and tested in accordance with the National & International standards.

(Power Factor Improvement) Plant

Power Factor Improvement (PFI) Plant with power Capacitor Banks, Magnetic AC Contactors, High Rupturing Cartridge (HRC) Fuses which are imported from Germany, Italy, Spain, France, Japan and Korea are manufactured.

PFI Plant is used to improve the power factor of the inductive loads in the electrical network by Capacitor Banks. The capacitors are of low losses and with inbuilt discharge resistor. The use of appropriate rating of PFI Plant reduces undesirable wastage of power. All control & indicating devices are located on the front door of the panel for easy viewing & operating.

This geometric relationship of apparent power to Active Power is traditionally expressed by the right triangle relationship of : Cosø=P.F=kw/kva

Synchronizing Panel

Synchronizing as we know is important from the point of view that how loads sharing between different unit’s takes place and load transfer during the maintenance is important. Panels require two or more different sources of power likewise between DG SETS and the main GRID. Synchronizing panel is used where one DG set synchronizing with two or more DG set when mains fail all DG start at a time but after some time one will be on & other will be stop as per load demand .When load increased above 70% of the total load the 2nd dg will be start & it synchronies with first one & total load was distributed equally On that two DG set & this process will go on. During low load we can run any single unit, and synchronize more units as the load increases. This can be manual or automatic.

Motor Control Center

MCC (Motor Control Center) panels are manufactured in free standing design both in cubical and compartment type with fixed or withdraw able facility. MCC’s are designed to facilitate easy handling, installation and maintenance of starters.

Light Distribution Boards

Distribution Boards also known as LDB’s are used to protect the appliances under short circuit and over load conditions. The distribution boards are of two types.

The distribution boards are designed and fabricated in various shapes, wall mounted or flush type, indoor or outdoor in various international protection standards to meet the desired requirement.

Power Distribution Boards

Distribution Boards also known as PDB’s are used to protect the appliances under short circuit and over load conditions. The distribution boards are of two types.

The distribution boards are designed and fabricated in various shapes, wall mounted, flush type and floor mounted type, indoor or outdoor in various international protection standards to meet the desired requirement.

PLC Panels

A Programmable Logic Controller, PLC or Programmable Controller is a digital computer used for automation of electromechanical processes, such as control of machinery on factory assembly lines and control of Electric supply to various electrical loads. Successfully interfaced with the panels and is installed in various Industries.

Auto Transfer Switch

(Auto Transfer Switch) Transfers load from main supply to generator or main supply according to operational sequence as programmed. These Panels can also be supplied with manual over ride system.

Auto Main Failure

(Auto Main Failure) This system consists of microprocessor based control module, to monitor the presence of city power and enables switching device to start the generator in case of power failure in a specified time as programmed.

Variable speed Drive Panels

Your choice depends on many application-specific factors such as ambient conditions, type of loads, duty cycle, maintenance accessibility, horsepower range, sequencing, and more. Brief guidelines have been developed to provide you with a basic understanding of the differences between AC and DC drive technologies. If you have specific questions, or require application/selection assistance, please inquire for further assistance from us.

Electric Meter Boxes

Industrial Power Tech is the principal Electric Meter Boxes manufacturer and supplier, offering Meter Boxes in the national trade markets. This Electric Power Meter Boxes are diligently designed by the expert that ensures their reliable functioning in various industrial applications.

Feeder Pillar

Feeder Pillars are used to control area / street lighting through photo electric cell. Feeder pillars are totally enclosed, metal clad type, weather proof, sheet steel fabricated and consists of bus bars, circuit breakers, magnetic contractors etc. We can also provide you feeder pillar with GRP Enclosure.

Load Takeoff Panels

Bus Tie Duct

Exclusive range of LT bus ducts, widely used in various industries & commercial projects for several applications.
High Breaking Capacity
Easy to Install
Easy Operation
Smooth Functioning
Can with stand High Temperature and Heat
High Functionality

Cable Trays & Cable Ladders

We have achieved great expertise in wide range of cable trays and cable ladders, by using latest technology and high grade raw materials. These have widely appreciated in electrical industry for their superior performance.

We also produce perforated cable trays and cable ladders from superior quality of MS, GI, SS, sheets in various thicknesses from 1.2 mm to 3 mm & in variety of shapes to meet the client’s requirements.

We have also inhouse Powder Coating facility

Kiosk